Nokta Makro The Legend

The Legend has launched!

Nokta Makro continues to knock down barriers by launching their latest waterproof simultaneous multi frequency metal detector, which by the specs, looks like a very impressive machine.

The Simplex+ was the companies breakthrough machine in the market, proving that you can really pack a lot of features on to a detector at an entry level price point. Nokta Makro had listened to the needs of their customers and added the features they wanted, all while keeping the costs low – and it proved to be really successful.

The Simplex+ may be a great value for money detector, however it does have its drawbacks. It runs only on one frequency (12 kHz) while it’s competitors were bringing out simultaneous multi frequency metal detectors to the market at a similar price point.

If you would like to read up more on frequencies and the benefits of simultaneous multi frequencies, click here to read the article:

The Simplex+ also had a wobble in the lower shaft when it was first released, flexed way too much, so Nokta Makro came out with a fix by which you could place a little plastic piece in the shaft but it really didn’t help as much as it should have, and it still flexes too much for my liking. So they came out with a carbon fibre lower shaft which sells separately, and that does in fact solve the issue.

Simplex+ works great on most ground conditions but being waterproof, the beach is where you going to want to take it if you live near the coast. This is where I have a love / hate relationship with the Simplex. I love the fact that its waterproof and that it can work at the beach but (and it’s a big BUT), you have to dial in the settings correctly to get it run as stable as possible on the wet sand or in the water. This means, going into the settings, dialling down the ground balance to zero in most cases for my local beaches, dropping the sensitivity down and only then you pretty much good to go – but at the cost of depth. It’s definitely not the deepest machine I have used in the wet sand or in water. However, and this is where the love comes straight back in, you just can’t find a lower priced machine that is fully waterproof and that can work on the beach. If you wanted a machine that can go deeper and work flawlessly at the beach, you better get out your wallet and pay for a much more expensive machine.

This is where The Legend comes in… and we welcome it with open arms. Now bear in mind I have not tested this machine yet but just going according to what was spoken at the live launch event and on the specs of the machine but it seems it will fill that gap. For customers who want to be able to use a machine at the beach, this machine is waterproof like its Simplex+ brother, but with its simultaneous multi frequencies and other upgrades, they claim this machine will work fantastically well at the beach, out the box, without even needing to ground balance. A pretty much turn on and go beach machine which should punch deeper and be a pleasure to use in most conditions.

It comes standard with a carbon fibre lower shaft, so should be no wobble issues like the original Simplex had and also boasts some new features such as the FerroCheck feature. This new feature makes it super easy to distinguish between modern trash like bottle caps and good targets. If it works as advertised, this new feature could be a game changer as FerroCheck saves you time by digging less trash!

The next newest feature is the addition of a Gold Prospecting mode. If out hunting for elusive little nuggets, just simply switch to this new mode and hunt away. Again, this is where all those extra frequencies really come into play into making this a truly versatile detector.

The detector will be sold in two versions, the WHP version and the Pro Pack version. It is important to note, that both versions will contain exactly the same detector, you just get added extra products with the Pro Pack version.

Both versions come with The Legend detector, the Bluetooth aptX wireless headphones, and a 11″ DD search coil. The Pro Pack adds and extra smaller 6″ coil as well as a waterproof external spare battery and charger.

Now don’t get me wrong, the Simplex+ is still a very capable entry level machine and will continue to be a great value machine for the price. The Legend is not here to replace the Simplex, it will cost more than the Simplex and it’s to fill a gap in their lineup for those wanting or needing even more from their machine.

Pricing in South Africa will be R12499 for the WHP version and R14999 for the Pro Pack version and we are currently accepting pre-orders on these machines.

If you would like to find out about all the features of this new machine, or would like to pre-order, you can click here to view the product:

 

What does the frequency mean?

This article relates to VLF (Very Low Frequency) metal detectors, which account for most hobby detectors as well as some gold detectors on the market today.

If you look at the specifications of the metal detector, you will find a frequency that the machine runs at.

Some examples:

Garrett ACE 200i – 6.5 kHz

Nokta Simplex+ – 12 kHz

Minelab Equinox 800 – Multi, 5, 10, 15, 20, 40 kHz

Nokta Gold Kruzer – 61 kHz

So what do these numbers actually mean and should you worry about them?

Well this depends, if you a just want a machine to have some fun with in the park to see what you can find, then no, it’s not all that important, however if you are looking for a specific item like shallow gold, then yes, you would want a machine that runs at the correct frequency to help best find what you looking for.

Let’s start with depth – The lower the frequency, the better depth you will get. As you start increasing the frequency, you will start to sacrifice on depth.

Well that’s easy then, we all want as much depth as possible, so let’s all use machines that have low frequencies then…. well no, it’s not quite as simple as that which brings me to my next point…

The size of the target – To find really large targets, you would want to use a low frequency. A massive drain cover for example, a low frequency here will be perfect as you looking for a large target and will get you the best depth. Now if you out to look for tiny sub gram gold nuggets, then you would not want to use a low frequency but rather a much higher frequency. By using a high frequency, when you sweep over the tiniest target it can provide a good solid signal whereas a really low frequency could miss this tiny target altogether. The higher the frequency is, the smaller the target can be while still receiving a good signal from the detector as sensitivity is increased.

The conductivity of the target – Different metals have different conductive properties. Silver for example is a high conductive metal whereas gold has low conductive properties. Low frequencies are better suited to high conductive metals (such as silver) whereas high frequencies are better suited to low conductive metals (such as gold).

So that is why you will notice that most VLF Gold Machines are considered specialist machines which run at a much higher frequency than most hobby detectors for these exact reasons – to be able to provide a solid signal to the tiniest of sub gram gold nuggets out in the goldfields as well as to provide a good hit on the low conductive properties of gold. The Minelab Gold Monster runs at 45 kHz, Nokta Gold Kruzer 61 kHz and XP ORX with 9.5″ elliptical coil has selectable frequencies from 14 kHz all the way to 81 kHz, making it an excellent choice for gold prospecting as you can change the frequency depending on ground conditions (The higher the frequency, the more susceptible the machine will be to giving false targets in highly mineralised ground due to the increased sensitivity).

Some metal detectors come with one frequency only which can be limiting, some come with a range of frequencies that you can manually select from and some of the newer machines come with a multi frequency option which can run at multiple frequencies simultaneously.

I would suggest that it is usually better to manually select one frequency if you searching for something in particular, otherwise run on multi frequency if your machine has that option to give you the best average of all the frequencies to give a good signal on a wide range of metals.

Here is a video that Minelab posted on their multi IQ technology which uses multiple frequencies simultaneously:

The Minelab Equinox and Minelab Vanquish range all use this newer multi iq technology which give them a slight edge over single frequency detectors.

This is not to say that a low frequency machine cannot find gold or a high frequency machine cannot find silver – this is not the case at all but it just improves the detectors ability to find exactly what you searching for – using the best tool for the job!

Best entry level metal detector 2020

 

Being a metal detector dealer, I regularly get asked which is the best entry level machine for a beginner to buy?

This is an understandable question as it can be quite daunting with all the different machines available on the market and what features they have to offer.

So this will be a very basic guide (for full disclosure, I only sell Garrett, Minelab, Nokta Makro and XP Metal Detectors, so although there are other brands out there, I will only focus on the big brands that I sell as those are the machines I am more familiar with).

I will try and keep this article as unbiased as possible and just lay down the facts so you can draw your own opinion on which machine you think will be best suited for your needs.

Before we look at the machines, lets start with the different brands, where they from and when they were established:

Garrett –  Started in 1964, Made in the USA.

Minelab – Started in 1985, Australian company and manufacture to military grade standards.

XP Metal Detectors – Started in 1998, a French manufacturer but since they don’t offer a competing entry level machine in this market, we won’t discuss them further in this particular article.

Nokta Makro – Started in 2001 in Turkey as Nokta Detectors and acquired Makro Detectors in 2014 becoming Nokta Makro.

Now lets turn to the machines themselves:

Firstly, this article is intended for those who are looking to purchase their very first metal detector as a hobby. Something to use at the park, field or the beach. If you looking for a gold detector to look for gold nuggets in Africa, this is not the list to be looking at. I have created a separate article on “Best Gold Detector for Gold Nuggets” and that can be found by clicking here.

If we looked at this same question of “which machine is best for a beginner” a few years ago, the internet generally was pretty standard with the answer. That answer was the Garrett ACE 250 but we do however live in an ever changing world where technology is continually being improved and that is certainly no longer the case.

 

So as of July 2020, these are the front runners of entry level machines (which will probably change by next year again)!

 

Nokta Simplex+

 

The team at Nokta Makro have done an incredible job of packing the most features as possible into a very cost effective unit and making it as easy as possible to use. Undeniably, the best value entry level machine on the market today. Due to its low price point and feature rich offerings, this has become an extremely popular detector, both for first time users as well as more experienced users wanting a backup machine. This is the only detector in this entry level market that is fully waterproof.

PROS:

  • Low Price
  • Fully waterproof (submersible down to 3 metres)
  • Built in wireless module (Which allows you to use the optional Nokta Green Wireless Headphones with the machine)
  • Vibration Setting (Great for the hearing impaired or when detecting underwater)
  • Lighting (Simplex+ has it all: LCD Backlight, Keypad Backlight and built-in LED Flashlight)
  • Built in rechargeable battery
  • Software updateable when new features get released for this detector.

CONS:

  • Only uses a single frequency of 12 kHz
  • Very chatty under some circumstances (Does not run as quiet as some other machines in this market)
  • Target ID’s can jump around more than other machines in this market, depending on the soil conditions.
  • At the beach, the machine can at times have difficulty in auto ground balancing (This can be easily corrected by manually lowering the ground balance to 0.0 in difficult beach conditions)
  • If not correctly ground balanced at the beach, false signals will be introduced which can be confusing for a beginner.

Two options are available when purchasing the Nokta Simplex+

The Standard Nokta Simplex+

https://treasurehunters.co.za/home/nokta-simplex-

The Nokta Simplex+ WHP (Wireless Headphone Package) – which is exactly the same detector but it just comes bundled with the Nokta Wireless headphones and a Simplex cap as extras.

https://treasurehunters.co.za/metal-detectors/nokta-simplex-whp-wireless-headphones-package

 

 

Minelab Vanquish

 

Minelab has recently introduced the Vanquish range to its detector line-up. Minelab has created an extremely easy to use, turn on and go style of detector aimed at the novice user. This machine just works straight out the box without too much worrying about having to ground balance or having to play around with too many settings. It does not have all the features of the higher end machines but the performance is certainly there that can rival the best of them.

PROS:

  • Price (The basic Vanquish 340 model is the cheapest of the entry level machines mentioned in this article at time of writing)
  • Multi IQ technology (Minelab has created the use of simultaneously using multiple frequencies within their newer detector range and this certainly gives improved target ID and depth performance under difficult soil conditions – see video below)
  • Very stable at the beach, even on the wet sand, without the need to ground balance and therefore reducing any false signals.
  • Decent depth in difficult conditions
  • Runs quiet (no constant chatter)

CONS:

  • Coil is waterproof but the control box is not, so this machine can not be submerged under water.
  • Runs on AA batteries (some may see this a pro and not a con as its easy to change out batteries in the field, however we see built in rechargeable batteries being the better option here)
  • Only the top of the line Vanquish 540 model has built in bluetooth in order to use wireless headphones, the 340 and 440 model is stuck to using on board audio or using wired headphones.
  • The basic Vanquish 340 model lacks coming bundled with any headphones or rain cover, where the rest of the model lineup includes these items.

Four options are available when purchasing the Minelab Vanquish:

Minelab Vanquish 340

https://treasurehunters.co.za/metal-detectors/minelab-vanquish-340

Minelab Vanquish 440

https://treasurehunters.co.za/metal-detectors/minelab-vanquish-440

Minelab Vanquish 540

https://treasurehunters.co.za/metal-detectors/minelab-vanquish-540

Minelab Vanquish 540 Pro Pack

https://treasurehunters.co.za/metal-detectors/minelab-vanquish-540-pro-pack

Here is a video explaining Minelabs Multi IQ Technology:

Here is a diagram explaining the differences between all the models:

 

 

Garrett ACE APEX

 

The Garrett ACE APEX is the newest of the entry level machines to hit the market in 2020. It certainly has a nice upgrade with a fresh, modern look compared to the older ACE models. This is now the top of the line ACE model which is massively improved compared to the older ACE models.

PROS

  • Multi Flex Frequency Technology (Uses simultaneous multiple frequencies or can choose to select from individual frequencies)
  • Multi-Salt mode which is great for the wet sand at the beach
  • Built in rechargeable lithium ion battery
  • Built in Z-Lynk wireless technology (Can be used with optional Garrett Wireless headphones)

CONS

  • Coil is waterproof but the control box is not.
  • Price – slightly more expensive than the other machines mentioned in this article.

Garrett ACE APEX

https://treasurehunters.co.za/treasure-detectors/garrett-ace-apex

 

All these machines plus others can be purchased from our metal detecting store online – we deliver anywhere in South Africa to your door with full tracking.

https://www.treasurehunters.co.za

Best Metal Detector for Gold Nuggets – Buyer’s Guide

I came across this fantastic guide from Smarterhobby.com – so all credit goes to Mark Orwig for writing this article. (Some products and prices changed to fit in line with the South African market)

 

E​ver since James Marshall’s 1848 discovery of gold at Sutter’s Mill, prospecting in the United States has been the ultimate treasure hunt.

Prospecting gold nuggets with a metal detector is a thrilling hobby that’s both fun and (financially) rewarding.

But with so many machines on the market, how do you know which is the best metal detector for gold?

This go-to guide is packed with useful information that will help you make the right choice so you can start digging your very own gold.

How to Choose​

Before we get started, I want to make a public service announcement if I may.

All metal detectors will find gold nuggets if they’re in the ground (and big enough) – not just gold detectors.

A gold metal detector is simply a detector designed specifically to detect tiny targets in mineralized ground. That’s pretty much it.

So what makes a good gold detector?

It may surprise you that it’s much easier than you think to choose the right detector.

Some of the biggest factors include:

  • Where (geographically) you’ll be doing most of your prospecting.
  • The size of gold nuggets that have been found there in the past. If you don’t already know, I recommend joining a local prospecting club or talking to local claim owners.
  • Ground conditions. Is it highly mineralized? Is there a lot of trash?
  • Other uses. Do you want to use the same detector for coin, jewelry or relic hunting?
  • Budget.

You’ll need to ask yourself these questions before you even consider which detector you’ll buy.

Spoiler alert: there is no universal ‘best metal detector for gold’.

Although the GPZ 7000 is close for those of you who can afford a detector that’s the same price as a car.

The question should be, what is the best gold detector for your answers to the above questions?

Just because the Minelab GPX 5000 costs more than 6x the amount of a cheap VLF machine, doesn’t mean it’s better.

If I were hunting in low/moderate ground on top of bedrock in an area where the nuggets tend to be small, I would actually opt for a cheap VLF machine over the GPX 5000.

Am I crazy? No….not the last time I checked anyway…

Now let’s dive into the reasons why this is the case by deciphering the most important elements of any gold machine.

Detector Technology

The first thing you have to decide is which technology to use – VLF or PI.

VLF stands for Very Low Frequency and is the same technology used in detectors built for coins, jewelry, and relics.

VLF detectors broadcast at frequencies measured in kilohertz ranging from 3 kHz to 70 kHz.

Here are five reasons why you might choose a VLF over a PI

  • You’re a beginner.
  • You want to use the same detector for other detecting like coins, jewelry, relics.
  • You’re hunting for small to medium sized nuggets at depths under 20cm (most common).
  • You’re hunting in areas with lots of trash and need to discriminate.
  • You want to spend less than R20000

PI stands for Pulse Induction and is used in specialty detectors designed for maximum depth in highly mineralized ground.

PI detectors broadcast pulses and are measured by pulses per second.

Here are five reasons to opt for a PI machine over a VLF:

  • You’re an experienced gold hunter.
  • You want a specialty machine built just for gold nugget hunting.
  • You’re hunting for larger gold nuggets at greater depths AND aren’t so much interested in the smaller, shallower nuggets.
  • You’re hunting in highly mineralized ground with low levels of trash.
  • You have over R20000 to spend.

Now that we’ve identified the two camps let’s talk about some technical differences.

Operating Frequency

We already discussed that VLF detectors are best when searching for nuggets that are small to average in size.

The next thing to decide is the operating frequency of the VLF.

As mentioned above, VLF machines typically range from 3 kHz to 70 kHz with the most popular gold VLF machines in the 13-50 kHz range.

That is a huge range. So which is better?

Again we go back to nugget size.

Side note: This guide is not about where to find different sized nuggets, but larger nuggets will most often be at the highest elevations of your site, while the smallest will be at the lowest elevation – usually in a stream bed.​

In the United States, larger nuggets are most often found in Alaska, medium in Western States, and small in Eastern States.

The biggest and best nuggets in the world are typically found in Australia. (* Africa has also been known to produce plenty of small to large sized nuggets)

Now back to the techy stuff…​

There is an inverse relationship between frequency and nugget size (as well as maximum detection depth).

Both lower frequency VLF and PI detectors will find larger nuggets at greater depths – but will struggle to find smaller nuggets at shallow depths.

Alternatively, higher frequency VLF machines are better at finding smaller nuggets at shallow depths – and struggle to get greater depths.

So which is better? Well, neither…

It all depends on your particular area and the what’s been found there before (and at what depths).

The same concept holds true for coil size. Again there is an inverse relationship where larger coils get bigger targets at greater depths, and smaller coils get smaller targets at shallow depths.

Smaller ​coils are also better for rocky areas where you need to maneuver around large rocks and get into tight spaces.

They’re also preferred over large coils in highly mineralized ground​ since they will ‘see’ less of the ground at any given time.

Let’s revisit my comparison at the beginning of this article between the GPX 5000 and a cheap VLF machine to help understand my reasoning.

The Gold Monster 1000 is a 45 kHz VLF machine with a small, 5” coil.

The GPX 5000 is a PI machine with a large 11” coil.

So if you’re hunting on bedrock in an area with small nuggets and ground that is not highly mineralized, the Gold Monster is the clear choice.

Using the GPX 5000 in this scenario might actually cause you to miss nuggets altogether!

I don’t know about you, but I’d rather dig several small nuggets than no nuggets at all because my machine is only looking for large ones.

For more information on frequencies, have a read through this article: https://treasurehunters.co.za/

Mineralization

Another factor in determining what range of frequencies to look for when choosing a gold detector is the ground mineralization for where you’ll be hunting.

After all, gold is most commonly found in areas of mineralization – at least to some degree.

Lower frequency VLF and PI machines will handle high mineralization much better than high-frequency VLF.

If you’re in areas of extreme mineralization such as black sand in a stream bed, then a PI will likely be your only option as it will see through the ground and not false.

So you probably don’t want to hunt with a cheap VLF machine for example if you’re in areas of high mineralization if you want to avoid constant falsing.

Another feature to consider when dealing with mineralization is the ground balance.

Almost every gold detector comes with automatic ground balance (or ground tracking) – but not all ALSO have manual ground balance.

So I recommend you invest in a machine that has both forms of ground balancing.

Is your head spinning yet?

It’s really not as complicated as I’m making it sound.

In fact, it’s probably more complicated for me to explain all this in writing than it is to decide on a detector.

Discrimination

In addition to the varying degrees of ground mineralization, you also need to consider how much trash is in the ground.

Now I use the term trash loosely here. When I say trash, I’m referring to anything that’s not gold.

VLF detectors have the advantage of electronic metal discrimination – meaning you can choose to ignore trash signals and only focus on good, gold signals.

Alternatively, PI detectors either struggle with discrimination or have none at all.

So if you know you’ll be in areas with a high trash density, you might do well to opt for a VLF detector. Otherwise, you’ll spend your entire day digging trash.

Parting Words​

That wasn’t so bad, was it?

If you’re new to metal detecting and these concepts are not already familiar to you, I recommend reading this article a few times.

Once you understand everything we’ve talked about in this article, your biggest question should be: “What if I want to find both small shallow, small nuggets, AND large, deep nuggets?”

Excellent question!

The reality is that unless you can anti-up for a Minelab GPZ 7000 (currently R168000 MSRP), you’re going to want two machines.

My best advice is to get a VLF machine for your small, shallow gold, and whichever of the Minelab PI machines your budget allows for the deep, larger nuggets.

Accessories

Now that you have a better idea of which gold detector is best for you, here are a few accessories I highly recommend for all prospectors:

  • Plastic scoop to wave dirt/rocks over coil during recovery.
  • Pick to hammer through rocky ground
  • Pinpointer or coil probe to quickly pinpoint those small nuggets
  • Coil Cover to protect your coil from damage
  • Vials to store your fine gold
  • Shoulder or chest harness to take the weight of the detector off your arm
  • Different coils to adapt to the location your hunting
  • Headphones to hear those faint gold signals
  • Strong Magnet to quickly pickup iron trash and ‘hot rocks’ before digging

End of article

MY RECOMMENDATIONS (in conjunction with Mark Orwigs’ recommendations)

For Intermediate and Expert Nugget Hunters (Best of the Best)

  • Garrett ATX: Submersible to 10′, a PI gold detector also great for saltwater and relic hunting. Easy to use, excellent value for money.
  • Garrett ATX (Deepseeker Package): Includes a 20″ coil for finding those deep large nuggets. A hard case is also included in this package, best value for money.
  • Minelab SDC 2300: Easiest expert-level detector to use for less serious gold prospectors, most compact for easy travel
  • Minelab GPX 5000: For serious gold prospectors. Most coils and accessories. – good for deep large nuggets
  • Minelab GPX 6000: Newer, lighter and easier to use then ever before.
  • Minelab GPZ 7000: Best of the best (and most expensive) – best for both deep large and small shallow nuggets

* The GPZ 7000 uses Zero Voltage Transmission (ZVT) which effectively gives you two machines in one – a deep PI machine, and a high frequency VLF machine.

For Beginner and Intermediate Nugget Hunters

  • XP ORX with 9.5″ ellipitical HF coil: The lightest machine on the market and you can manually select from a wide range of frequencies from 13 kHz to 81 kHz.
  • Minelab Gold Monster: Automatic sensitivity and ground tracking, operates at 45 kHz – best for shallower small to average size nuggets
  • Nokta Makro Gold Kruzer: Waterproof, wireless headphones and 61 kHz – best for fine gold / jewellery and shallower small to average size nuggets
  • Nokta Makro Gold Finder 2000 – Extremely easy to use, turn on and go! – best for shallow small to average size nuggets
  • Garrett Goldmaster 24K – Easy to use, 48 kHz for super sensitive gold finds. Rainproof and automatic ground balance.

* All gold detecting recommended machines can be purchased from Treasure Hunters Online Store in South Africa.

Minelab Equinox 600/800 Update 2.0

The latest update for the Minelab Equinox series of metal detectors has been released. If you have not updated yours already, here is a brief run down on how to do it and why you should be doing it.

Follow this link to download the latest Minelab Update Utility (MUU) to your computer (you can choose a windows or mac version depending on your computer): https://www.minelab.com/equinox-software-update-2-0?fbclid=IwAR38OUO6DpuSjdwSUtP2WvV3x5DKUfVIX1hF6-3iLlcsUJnNd_MV-fbHRnM

Once the MUU is downloaded, open the application and follow these instructions:

1. Connect the EQUINOX to the computer USB port using the magnetic charging cable and turn on the detector.
2. When the EQUINOX is identified, the MUU will communicate with the detector and determine the current software version.  
3. If an update is available, the MUU will display Updates are available for your detector. Click INSTALL to begin the upgrade or QUIT to close the MUU.
4. If the metal detector is up to date, the application will display Your detector is up to date and prompt you to QUIT the application.
5. The EQUINOX screen will go blank during the update; a green LED on the top left corner of the control box will blink rapidly while the update is in progress.
6. Installation will take approximately 1 minute.Once the upgrade is complete, the EQUINOX will restart and the MUU will prompt you to disconnect the detector and QUIT the application.Note: Close the application and reopen if updating multiple EQUINOX detectors 

WHAT IS NEW?

Difficult ferrous targets — the common enemy for all detectorists. That is until EQUINOX. Hit the download on our EQUINOX update to make those pesky bottle caps, rusty nails and other falsing targets a thing of the past. Fire up the Minelab Update Utility and you’re on your way. It’s simple. You’ll experience the enhanced Iron Bias feature, improved EQUINOX 600 backlight and much more.

Improved Iron Bias

Iron Bias has been enhanced with the addition of a new Iron Bias settings profile. The original EQUINOX Iron Bias ‘FE’ settings will still be available, but there is now the option to switch to the new Iron Bias ‘F2’ settings, which have an improved capability to reject a much wider range of difficult iron targets, including bottle caps.

EQUINOX 600 Backlight Brightness

The EQUINOX 600 now has the ability to adjust the backlight brightness to an additional ‘Low’ setting that matches the minimum setting on the EQUINOX 800. This ‘Low’ brightness is ideal for detecting at night and in low light conditions.

Conclusion

It’s great that Minelab is able to provide us with these updates. For the detectorists with the Equinox 600 that enjoy hunting at night will find a huge difference with the screen brightness. Previously there was only two settings: Very bright and Off, which the bright setting was too bright at night and most people would choose to switch the brightness off completely. Now we can enjoy a nice dim screen backlight during our night hunts.

The new iron bias looks like a neat upgrade to which will help with those rusty bottle cap signals. What used to sound like a good digging signal will now be eliminated completely or made to sound like an iffy, jumpy signal.

The one thing to bear in mind though, is after the update the new iron bias setting has not been selected. You need to manually change this in settings as follows:

In the settings menu, get to the recovery speed setting and then press and hold down the setting button for approx 2 seconds. This will take you from the recovery speed setting to the iron bias setting and you will see “Fe” on the screen. “Fe” is the original iron bias setting, you will need to press the accept/reject button to change this to “F2” which means the new and improved iron bias setting is set.

You will need to change this on each and every mode you would like to change the iron bias setting. For example you may choose to keep “Fe” setting on Park mode 1 but the new “F2” setting on Park mode 2 etc.

I look forward to digging less rusty bottle caps and enjoy the new dimmer brightness on the screen. Thank you Minelab, may you continue to send us new improvements as they become available.

Treasure Hunters Online Shop

A few months ago, I launched the online store for Treasure Hunters and its been growing from strength to strength.

I would like to take this opportunity to thank each and everyone who has purchased from our online store. The support has been truly amazing and I appreciate every single sale made.

Its been an incredible journey thus far and cant wait to see what the future holds for the online store.

We will continue to add more products in the coming months but more importantly we will always strive to ensure you have a pleasant shopping experience through ease of use as well as excellent customer service.

Online shopping is certainly a convenient way to shop, as it just takes a few clicks from the comfort of your own home in order to get your products delivered to your door in just a day or two!

If you thinking of purchasing any metal detecting equipment, please try our online store for your next purchase.

www.treasurehunters.co.za

We look forward to welcoming you to our store in cyberspace. Its open 24/7 🙂

 

The hole that keeps on giving

If there was only one thing I could advise you on, just one thing, it would be to check your holes again after digging a target.

Get into the habit of always ensuring there really is nothing left in the hole before covering it back up.

I went for a little beach hunt the other night and really was not finding anything (beach was sanded in) but then came across this one hole on the dry sand… the hole that kept on giving.

Started off with just a single tone, dug and found a 1 dollar coin. Bingo, before covering up, lets just check that there is nothing left in the hole, bang, another signal – another $1 coin! Check again, another $1 coin.  Hole getting deeper now, repeat process and got 2 different signals, dug and found another $1 coin and a fifty cent coin. Checked again, another $1 coin. This hole kept me busy for a good few minutes which was great cause the rest of the beach was pretty dead. All in all, I got 10 coins out of this single hole, giving me a total of $9.50.

This is certainly the most amount of targets I have ever found in one hole (perhaps someone lost all their money out of their pocket and it fell all in the same spot or perhaps there is another bizarre explanation) but either way, always double check your holes. You will be surprised how many times you find more than one target in the same hole.

 

The Difference Down Under

G’day mate and greetings from Australia!

I know I have not posted a blog entry for a long time, so for that I do apologise – it was not a case that I had stopped metal detecting but rather a case of not finding much… at all!

I am presently working in Perth, Australia ( I know I have moved around a lot, I do feel like a gypsy some days) so I will be blogging from here for a while (until the next move that is)!

So where to begin? Well let me start by telling you that metal detecting is pretty big here, I follow some Australian metal detecting sites online and there are many more active detectorists here than in South Africa. It seems to be a much more common and accepted hobby, lots of online and brick and mortar metal detecting stores and quite a common site to see someone detecting on the beaches or hearing stories of someone finding gold nuggets out in the goldfields.

Although I have done mostly night beach hunts here and have had the beach to myself (well, mostly to myself, will get to that later), I am led to believe that you will find a couple of detectorists hitting the beaches early in the mornings pretty much daily which in turn leaves me with less to find. To add to this, every morning a digger loader of sorts will come and scoop away a layer of sand at most beaches. The challenge keeps on getting tougher! So consider yourself lucky that in South Africa, the land and beaches are almost untouched with lots of goodies up for grabs with minimal “competition” out there.

The other problem I am faced with, which is a good problem in a way, is that it seems the Australians don’t litter as much on the beaches. As much as I am not finding any good finds, I am hardly finding much junk either. The problem with this is that it is highly boring swinging your arm off for hours and hardly getting any signals. This has happened all too often.

I must be honest though, I have always gone hunting at the “wrong time”, either the tides have been high and I am faced with dry sand detecting or too much sand out and about so that has not helped my cause either. I have seen some great cuts (which I have not seen in Cape Town) but never had my detector with me or was not a good time for me to be out detecting. Now that winter is approaching however, I am expecting some big cuts to appear and will hopefully get the opportunity to be at the right place at the right time and a future blog post will reveal what the outcome will be.

The little junk I do find though is mostly bottle caps as drinking is allowed on the beaches. This brings me back to my story about being “mostly alone” on the night hunts, as I prefer to hunt when the beaches are quiet, I am often out at night – but so are those that are either cuddling or drinking on the beach. Once I had the beach to myself except for a couple cuddling on their blanket on the beach and as I approached closer they waved at me and so we started talking. They were a little drunk but very friendly and turned out the girl was also a South African (plenty of us here in Perth). They asked the usual questions as to what I was doing / looking for but all in all were extremely friendly and we said our goodbyes and I continued my detecting. On a different ocassion however, I came across two guys who clearly had way too much to drink and they thought it was time to give me a theory lesson on where I should be detecting – apparently Professor Drunk thought I should take my metal stick and go to the Thames and I will be sure to find some dinosaur teeth! To be honest, it was actually quite entertaining at the time but I quickly brushed them off to continue my hunting – which well, produced nothing. Perhaps I would have actually had better luck searching for those dinosaur teeth after all. I have also on a couple of ocassions witnessed some late night skinny dipping from groups of girls and guys – the things you see at the beaches at night!

Pull tabs seem to be a thing of the past for me, don’t get much of them here but instead we have a circular piece of foil (see picture below). These are on all the Energade kind of drink bottles which you peel off before you can drink out the bottle. Damn the signal of these sound just like gold, luckily I am learning on my CTX what numbers to ignore, however if I ignore them, I don’t have much to dig – its all pretty bittersweet.

 

foil

Fools Gold

While beach detecting, you get a signal, scoop, clear the sand from the scoop and find nothing else but a ring left behind sitting in that scoop – what a feeling, that moment we all as beach detectorists love to treasure…

You quickly gather the ring from the scoop and try to examine it without anyone else around noticing, and what do you see – bingo – an 18ct stamp marked on the ring, Gold! Or is it??

This scenario happened to me last night, well all of it except for the “without anyone else around noticing” part, as my hunting buddy and I had the beach to ourselves. It was because of loadshedding (all South Africans will be extremely familiar with that term but if anyone is reading this from elsewhere, “loadshedding” is basically a term used when your energy provider thinks it’s funny to turn off all electricity in your neighbourhood for at least 2 hours at a time), I had a slight humour failure when I heard my house was going to be in complete darkness for 2 hours yet again and therefore decided to call on my hunting buddy and made plans for a little last minute beach night hunt.

Now the problem with the ring I found last night, was it did not quite look like you would expect an 18ct gold ring to look like. 18ct maintains its gold look very well , yet mine looked rather shabby, in fact so much so that even my hunting buddy had to have his say “Congrats buddy, but erm, you might want to get that one checked out before you get too excited”. You see, we both felt something was not quite right with an 18ct ring looking the way it did. But hey, it had a few small “diamonds” on top, it had the 18ct stamp, I was still deep down determined to believe it was gold.

On arrival back home, I got out my electronic diamond tester to check the little stones on top of the ring – Nothing – certainly not diamonds, this was not starting off well. Next step, I filed away a small portion of the ring in order to scratch away any surface plating in order to test the ring on my electronic gold tester. After filing away, a nice shiny gold patch appeared which gave me a glimmer of hope – but it was very short lived as my electronic tester gave me the big “NA” which is what the machine says when it means “Nice try but no gold here”.

Naturally, there could have been something not right with the machine, I mean how accurate are these things anyway right? So out came the acid test – again, it showed NO GOLD.

So lets summarise – We had our doubts because it did not look like 18ct gold, then the diamond tester said diamonds were fake, then electronic tester said gold was fake, then acid test confimed all above. Satisfied? Not a chance, so today I took it to the jeweller for a professional opinion, I mean after all it did have the 18ct stamp on. The jeweller confirmed it was indeed a fake and admitted that fakes do not happen often but it does happen more often than not. He was real nice though and even gave the ring a free clean.

I came home and cleaned it up some more so I could give you some before and after pictures of the ring and the stamp on the ring. So I guess the moral of the story is, even if you find gold with markings on – perhaps you might want to give it some further inspection, don’t just trust the stamp!

X
Add to cart